Polished Concrete Cost Calculator & Price Guide
Use this guide to estimate polished concrete cost for Australian homes, whether you are comparing polished concrete floors cost for a basic matte finish or a premium decorative surface. Polished concrete price typically ranges from $65/m² to $175/m² AUD, with final costs depending on the finish selected and whether the existing slab is in good condition or needs repairs.
Estimate polished concrete flooring cost
Rough guide based on Australian averages. Real quotes vary by site, finish and contractor.
- Finish:
- $3,250
Estimates are indicative only. For an accurate price, get free quotes from local tradies above.
Polished Concrete Price Breakdown
Typical job based on 50 m². Prices are supply-and-install midpoints — actual quotes will vary.
| Type | Cost per m² | Typical 50 m² job |
|---|---|---|
| Grind & seal (matte) | $65 | $3,250 |
| Salt & pepper (light exposure) | $95 | $4,750 |
| Full aggregate exposure | $140 | $7,000 |
| Decorative (coloured / patterned) | $175 | $8,750 |
What Affects Polished Concrete Cost?
- Finish level: The biggest driver of polished concrete floors price is the finish you choose. Grind & seal starts at $65/m², salt & pepper is $95/m², full aggregate exposure is $140/m², and decorative coloured or patterned finishes reach $175/m².
- Condition of the existing slab: If the slab is already in good condition, you pay the standard rate for your chosen finish. If it needs repair, add $20/m² before multiplying by the floor area, which can significantly increase the polished concrete cost per m2.
- Floor area: Concrete polishing cost per square metre is applied across the total floor area, so larger spaces naturally cost more overall. However, there is also a minimum job charge of $2500 AUD if the calculated amount falls below that figure.
- Estimate range: Displayed estimates are shown as a range using ±15% around the midpoint rate. This means the final polished concrete floors price per square metre may vary within that band depending on job specifics and site conditions.
Polished Concrete Cost - Frequently Asked Questions
Polished concrete cost per m2 generally starts at $65/m² AUD for a grind & seal matte finish and goes up to $175/m² AUD for decorative coloured or patterned concrete. Mid-range options include $95/m² for salt & pepper and $140/m² for full aggregate exposure. If the slab needs repair, add $20/m² to those rates before calculating the total.
For a typical 50 m² area in good condition, grind & seal is $3250, salt & pepper is $4750, full aggregate exposure is $7000, and decorative finishes are $8750 AUD. If slab repairs are needed, the rates increase by $20/m² before multiplying by 50 m². The displayed estimate range is then shown at ±15% around those midpoint totals.
Polished concrete floors price per square metre depends on the finish level selected. Grind & seal is $65/m², salt & pepper is $95/m², full aggregate exposure is $140/m², and decorative finishes are $175/m² AUD. These figures are based on supply and installation.
Polished cement floors cost is lower when the existing slab is in good condition because you only pay the base finish rate. If repairs are required, add $20/m² to the chosen finish before multiplying by the area. For example, a $95/m² salt & pepper finish becomes $115/m² when slab repair is needed.
There is a minimum job charge of $2500 AUD when the calculated polished concrete price falls below that amount. This means very small areas may not simply be charged at the per-square-metre rate alone. The minimum helps cover setup, labour and equipment costs.
The total is calculated by taking the concrete polishing cost per square metre for your selected finish, adding $20/m² if the slab needs repair, and then multiplying by the floor area. After that, the displayed estimate range is shown at ±15% around the midpoint. If the result is below $2500 AUD, the minimum job charge applies instead.