Supertrades

Bathroom Waterproofing Cost Calculator & Price Guide

Bathroom waterproofing cost in Australia usually depends on how much of the wet area needs membrane and whether the substrate is ready to go. For a typical bathroom waterproofing price, supply and install rates in AUD, per m² of floor area, range from $170/m² for a full bathroom up to $260/m² for a shower recess, with a $100/m² adder where the area needs repair before waterproofing can begin.

Estimate bathroom waterproofing cost

Membrane supply-and-install midpoints for Australia, priced per m² of floor area. Waterproofers often quote $50 to $100 per m² of membrane, which includes the walls, so the rate per m² of floor is higher. Tiling and tile re-lay are not included unless noted in your quote.

Condition
Good = substrate ready to membrane (new reno or tiles already off). Needs repair = tile strip-out, screed repairs or fall correction.
Estimated cost range
$650 - $900
≈ $800 midpoint

Your real price depends on your site. Local tradies confirm it after a look.

Free and no obligation. Vetted local tradies. Phone optional.

Estimates are indicative only. For an accurate price, get free quotes from local tradies above.

Find installers near you →

Compare installers on our Bathroom Waterproofing hub & request quotes when you're ready.

Bathroom Waterproofing Price Breakdown

Typical job based on 3 m². Prices are supply-and-install midpoints — actual quotes will vary.

TypeCost per m²Typical 3 m² job
Shower recess$260$780
Shower + floor$200$600
Full bathroom$170$510

What Affects Bathroom Waterproofing Cost?

  • Scope of waterproofing area: The biggest driver of water proofing bathroom cost is how much of the wet area is being treated. A shower recess is priced at $260/m², shower + floor at $200/m², and a full bathroom at $170/m².
  • Condition of the substrate: Condition changes the price because membrane can only be applied once the surface is ready. Good means substrate ready to membrane (new reno or tiles already off), while needs repair includes tile strip-out, screed repairs or fall correction and adds $100/m².
  • Detailing in shower zones: Shower areas generally cost more per square metre because they involve higher-detail work at the waste, hob and corners. That is why shower waterproofing cost is highest for a shower recess-only job.
  • Minimum job charge: Small bathrooms and partial wet areas can look cheap on a per-square-metre basis, but the minimum job charge still applies. If the calculated total falls below $500 AUD, the estimate is lifted to the $500 minimum.

Bathroom Waterproofing Cost - Frequently Asked Questions

Bathroom waterproofing cost is usually priced by area and scope. Mid rates are $170/m² for a full bathroom, $200/m² for shower + floor, and $260/m² for a shower recess, with a $100/m² adder if the area needs repair before membrane can be applied. Very small jobs are subject to a $500 minimum charge.

A 3 m² shower recess comes to about $780 at the midpoint. A 6 m² bathroom floor with a shower comes to about $1,200, and a 6 m² full bathroom comes to about $1,020. Displayed estimates vary by about ±18% around those midpoints, and very small jobs are lifted to the $500 minimum job charge.

For a shower recess only, the shower waterproofing cost is $260/m² supplied and installed. On a 3 m² example, that gives a midpoint estimate of $780 AUD before any condition adder. If the area needs repair, add $100/m².

Shower base waterproofing and waterproofing shower recess areas usually sit in the highest rate category because of the detailed work around the waste, hob and corners. The midpoint rate is $260/m², so a 3 m² shower recess example is $780 AUD, with a further $100/m² added if repairs are needed first.

Where the job includes the shower recess plus the bathroom floor membrane, the midpoint rate is $200/m². For a typical 3 m² area, that works out to $600 AUD before any repair-related adder. If the substrate is not in good condition, allow an extra $100/m².

Yes. If the area is not in good condition, there is a $100/m² adder. Good means substrate ready to membrane (new reno or tiles already off), while needs repair means tile strip-out, screed repairs or fall correction.

Ready for real quotes?

We match you with vetted bathroom waterproofing installers in your area.

Go to Bathroom Waterproofing hub →