Insulation Installation Cost Calculator & Price Guide
Insulation installation cost in Australia usually depends on the area being covered, the insulation type and how easy the space is to access. For a typical ceiling insulation installation or under floor insulation installation, supply and install rates in this calculator start from $20/m² for ceiling batts and go up to $65/m² for spray foam insulation, all in AUD.
Estimate insulation installation cost
Indicative supply-and-install midpoints for Australia. Rates cover materials and labour for a standard install. State rebates, major asbestos work and structural changes are usually extra.
Set to 0 to exclude.
Your real price depends on your site. Local tradies confirm it after a look.
Free and no obligation. Vetted local tradies. Phone optional.
Estimates are indicative only. For an accurate price, get free quotes from local tradies above.
Compare installers on our Insulation Installation hub & request quotes when you're ready.
Insulation Installation Price Breakdown
Typical job based on 120 m². Prices are supply-and-install midpoints — actual quotes will vary.
| Type | Cost per m² | Typical 120 m² job |
|---|---|---|
| Ceiling batts (R4-R5) | $20 | $2,400 |
| Blown-in / loose-fill ceiling | $28 | $3,360 |
| Underfloor batts | $25 | $3,000 |
| Wall batts (accessible cavities) | $30 | $3,600 |
| Spray foam insulation | $65 | $7,800 |
What Affects Insulation Installation Cost?
- Insulation type: The biggest driver of insulation installation cost is the product and area being insulated. Ceiling batts are $20/m², blown-in ceiling insulation is $28/m², underfloor batts are $25/m², wall batts are $30/m² and spray foam insulation is $65/m².
- Area size: This is an area-based calculator, so the more square metres you insulate, the higher the total cost. A larger home will cost more to insulate overall, while small jobs may still be subject to the $800 minimum job charge.
- Condition of existing insulation: If the space is empty or clear and ready to insulate, no extra condition charge applies. If old, damaged or wet insulation needs to be stripped before the new install, add $15/m², with access multipliers applying to that work as well.
- Access and add-ons: Easy access uses the base rates, but Restricted roof / crawl applies a ×1.2 multiplier and Low pitch / tight / 2-storey applies ×1.4. Optional extras can also increase the quote, including reflective foil / sarking at $1,400, remove old insulation at $1,200 and top-up over existing batts at $900.
Insulation Installation Cost - Frequently Asked Questions
Using the default 120 m² example, the cost insulate house figure ranges from about $2,400 for ceiling batts to $7,800 for spray foam insulation before any extras. With the calculator’s displayed estimate range of ±20%, that works out to roughly $1,920 to $2,880 for ceiling batts and $6,240 to $9,360 for spray foam. Access changes and add-ons can increase the final total.
For roof and ceiling areas, ceiling batts are priced at $20/m² and blown-in / loose-fill ceiling insulation is $28/m². On a typical 120 m² job, that equals $2,400 for batts or $3,360 for blown-in insulation before extras. If access is Restricted roof / crawl, apply ×1.2, and if it is Low pitch / tight / 2-storey, apply ×1.4.
Ceiling insulation installation costs $20/m² for R4-R5 ceiling batts and $28/m² for blown-in / loose-fill ceiling insulation. For 120 m², that is $2,400 or $3,360 at Easy access. If the ceiling space has old, damaged or wet insulation to strip before the new install, add $15/m² plus the relevant access multiplier.
Blow insulation cost is $28/m² for blown-in / loose-fill ceiling insulation, compared with $20/m² for ceiling batts. For a 120 m² ceiling, that is $3,360 for blown-in versus $2,400 for batts at Easy access. Blown-in products are often chosen for hard-to-reach ceiling voids.
Insulation batts installation is $20/m² for ceiling batts and $25/m² for underfloor batts. On a 120 m² project, that comes to $2,400 for ceilings or $3,000 for under floor insulation installation before extras. Underfloor insulation installers may also need to charge more where access is restricted, using the ×1.2 or ×1.4 access multipliers.
Spray foam insulation installers are priced at $65/m² in this calculator, making it the highest-cost option listed. For a typical 120 m² area, that gives a midpoint estimate of $7,800 at Easy access, with a displayed range of about $6,240 to $9,360. If removal is needed first, add $15/m² for the affected area, or select the optional remove old insulation add-on at $1,200 where applicable.
Ready for real quotes?
We match you with vetted insulation installation installers in your area.
Go to Insulation Installation hub →